Just How to Set up a Bath Tub: Set Up an Acrylic Tub and Bathtub Surround
Just How to Set up a Bath Tub: Set Up an Acrylic Tub and Bathtub Surround
Blog Article
Every person may have their own individual way of thinking in relation to Tools You Need to Install a New Bathtub .
Installing a bathtub isn't precisely brain surgery, however it does call for strong plumbing, woodworking, and also occasionally, tiling skills. Replacing an old bathtub with a new one is also a moderately difficult project. If the old tub is readily available, the job can move rapidly; if you need to open up a wall to eliminate the old tub as well as position the new tub, the task is much harder. In either case, the project is within a home handyman's skills, although you will certainly require an assistant to vacate the old bathtub as well as set in the new one. See to it you have actually certified on your own for the task as well as are comfortable attempting it. Instead of employing a specialist to take over a halfway-completed project, it is better to consider using one prior to you begin. Chances are you may require a specialist plumber to make tube links.
This short article will help you mount a brand-new tub in your washroom if you have actually currently purchased a new tub and don't require to change the setup of your previous water pipelines.
Your devices as well as material checklist ought to make up the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is disconnect the water. After doing so, activate the taps to drain any kind of water continuing to be in the system. The procedure of getting rid of the existing taps can be fairly bothersome as a result of the limited gain access to that is frequently the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the taps. Have a fabric ready for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Prior to moving on to fit the brand-new faucets, compare the pipeline connections on the old faucets to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly require a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a link to the current supply pipes.
If you require to fit a monobloc, after that you will require minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the faucet in the mounting hole in the bath/basin making sure that the washing machines are in location between the faucet and also the sink. Secure the tap in position with the supplier provided backnut. When the faucet is firmly in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal tap ports. The previous type must be attached to the tap ends initially, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Bath tub
Using the two wood boards under its feet, position the bath tub in the required setting. The wood boards are helpful in evenly spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four little points.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the tub up until the level reviews degree.
To mount faucets, fit all-time low of the outermost versatile faucet port to the proper supply pipeline by making a compression sign up with; then do the exact same for the other tap.
Switch on the water supply and check all joints and also brand-new pipework for leakages and also tighten them if necessary. Fill the bathtub as well as additionally examine the overflow electrical outlet as well as the typical outlet for leakages.
Finally, fix the bath paneling as explained in the producer's instruction manual. Tiling and securing around the bath tub needs to wait up until the tub has been used at the very least when as this will certainly settle it into its last placement.
Getting ready for the Setup
Firstly, the sustaining structure supplied with the bath needs to be fitted (if called for) according to the maker's instructions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to make certain that if the tap features a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps device to avoid strain on the bath tub.
Fit the versatile tap adapters to the bottom of the two taps making use of 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you make use of all of the provided washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must currently be ready to be fitted in its last position.
Tiling Around the Tub
In the location where the bathroom meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to split an inflexible seal, causing the water to permeate the wall surface in between the bath and the tiling, causing difficulties with wetness and also possible leaks to the ceiling below.
You can select from a selection of coloured sealers to blend in your fixtures as well as installations. They are marketed in tubes and also cartridges, and are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of soaked paper or soft rope. Keep in mind to constantly load the bath tub with water before sealing, to allow for the movement experienced when the tub is in use. The sealant can split rather very early if you do not think about this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also quickly offered on the market. It is recommended to fit the floor tiles making use of waterproof or water-proof glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was shown that write-up on Installing A Bathtub through someone on a different web blog. Are you aware of another person who is fascinated with Installing A Bathtub? Why not promote it. We appreciate reading our article about How to Install a Bathtub.
Set Up An Appointment
Report this page